terminfo(5)

NAME
terminfo - terminal capability data base

SYNOPSIS
/usr/pkg/share/terminfo/*/*

DESCRIPTION
Terminfo is a data base describing terminals, used by screen-oriented programs such as nvi(1), rogue(1) and libraries such as curses(3X). Terminfo describes terminals by giving a set of capabilities which they have, by specifying how to perform screen operations, and by specifying padding requirements and initialization sequences. This describes ncurses version 5.9 (patch 20110404).

Entries in terminfo consist of a sequence of `,' separated fields (embedded commas may be escaped with a backslash or notated as \054). White space after the `,' separator is ignored. The first entry for each terminal gives the names which are known for the terminal, separated by `|' characters. The first name given is the most common abbreviation for the terminal, the last name given should be a long name fully identifying the terminal, and all others are understood as synonyms for the terminal name. All names but the last should be in lower case and contain no blanks; the last name may well contain upper case and blanks for readability.

Lines beginning with a `#' in the first column are treated as comments. While comment lines are legal at any point, the output of captoinfo and infotocap (aliases for tic) will move comments so they occur only between entries.

Newlines and leading tabs may be used for formatting entries for readability. These are removed from parsed entries. The infocmp -f option relies on this to format if-then-else expressions: the result can be read by tic.

Terminal names (except for the last, verbose entry) should be chosen using the following conventions. The particular piece of hardware making up the terminal should have a root name, thus ``hp2621''. This name should not contain hyphens. Modes that the hardware can be in, or user preferences, should be indicated by appending a hyphen and a mode suffix. Thus, a vt100 in 132 column mode would be vt100-w. The following suffixes should be used where possible:

For more on terminal naming conventions, see the term(7) manual page.

  Capabilities
The following is a complete table of the capabilities included in a terminfo description block and available to terminfo-using code. In each line of the table, The variable is the name by which the programmer (at the terminfo level) accesses the capability. The capname is the short name used in the text of the database, and is used by a person updating the database. Whenever possible, capnames are chosen to be the same as or similar to the ANSI X3.64-1979 standard (now superseded by ECMA-48, which uses identical or very similar names). Semantics are also intended to match those of the specification. The termcap code is the old termcap capability name (some capabilities are new, and have names which termcap did not originate).

Capability names have no hard length limit, but an informal limit of 5 characters has been adopted to keep them short and to allow the tabs in the source file Caps to line up nicely. Finally, the description field attempts to convey the semantics of the capability. You may find some codes in the description field:

(P) indicates that padding may be specified

#[1-9]
    in the description field indicates that the string is passed through tparm with parms as given (#i).

(P*)
    indicates that padding may vary in proportion to the number of lines affected

(#i)
    indicates the ith parameter.

These are the boolean capabilities:
These are the numeric capabilities:
The following numeric capabilities are present in the SVr4.0 term structure, but are not yet documented in the man page. They came in with SVr4's printer support.
These are the string capabilities:
Set left (right) margin at column #1
set right soft margin at current column
Set right margin at column #1
set a tab in every row, current columns
Set top margin at current line
Set top (bottom) margin at row #1
current window is lines #1-#2 cols #3-#4
Start printing bit image graphics
Start character set definition #1, with #2 characters in the set
Stop printing bit image graphics
End definition of character set #1
List of subscriptable characters
List of superscriptable characters
tab to next 8-space hardware tab stop
Printing any of these characters causes CR
move to status line, column #1
select touch tone dialing
underline char and move past it
half a line up
User string #0
User string #1
User string #2
User string #3
User string #4
User string #5
User string #6
User string #7
User string #8
User string #9
wait for dial-tone
XOFF character
XON character
No motion for subsequent character
.nr 3crow 0
VariableCap-TCapDescription
.nr 3brule 1
.nr 3crow 1
StringnameCode
.nr 3brule 1
.nr 3crow 2
acs_charsacscac
.nr 3brule 1
.nr 3crow 3
back_tabcbtbt
.nr 3brule 1
.nr 3crow 4
bellbelbl
.nr 3brule 1
.nr 3crow 5
carriage_returncrcr
.nr 3brule 1
.nr 3crow 6
change_char_pitchcpiZA
.nr 3brule 1
.nr 3crow 7
change_line_pitchlpiZB
.nr 3brule 1
.nr 3crow 8
change_res_horzchrZC
.nr 3brule 1
.nr 3crow 9
change_res_vertcvrZD
.nr 3brule 1
.nr 3crow 10
change_scroll_regioncsrcs
.nr 3brule 1
.nr 3crow 11
char_paddingrmprP
.nr 3brule 1
.nr 3crow 12
clear_all_tabstbcct
.nr 3brule 1
.nr 3crow 13
clear_marginsmgcMC
.nr 3brule 1
.nr 3crow 14
clear_screenclearcl
.nr 3brule 1
.nr 3crow 15
clr_bolel1cb
.nr 3brule 1
.nr 3crow 16
clr_eolelce
.nr 3brule 1
.nr 3crow 17
clr_eosedcd
.nr 3brule 1
.nr 3crow 18
column_addresshpach
.nr 3brule 1
.nr 3crow 19
command_charactercmdchCC
.nr 3brule 1
.nr 3crow 20
create_windowcwinCW
.nr 3brule 1
.nr 3crow 21
cursor_addresscupcm
.nr 3brule 1
.nr 3crow 22
cursor_downcud1do
.nr 3brule 1
.nr 3crow 23
cursor_homehomeho
.nr 3brule 1
.nr 3crow 24
cursor_invisiblecivisvi
.nr 3brule 1
.nr 3crow 25
cursor_leftcub1le
.nr 3brule 1
.nr 3crow 26
cursor_mem_addressmrcupCM
.nr 3brule 1
.nr 3crow 27
cursor_normalcnormve
.nr 3brule 1
.nr 3crow 28
cursor_rightcuf1nd
.nr 3brule 1
.nr 3crow 29
cursor_to_llllll
.nr 3brule 1
.nr 3crow 30
cursor_upcuu1up
.nr 3brule 1
.nr 3crow 31
cursor_visiblecvvisvs
.nr 3brule 1
.nr 3crow 32
define_chardefcZE
.nr 3brule 1
.nr 3crow 33
delete_characterdch1dc
.nr 3brule 1
.nr 3crow 34
delete_linedl1dl
.nr 3brule 1
.nr 3crow 35
dial_phonedialDI
.nr 3brule 1
.nr 3crow 36
dis_status_linedslds
.nr 3brule 1
.nr 3crow 37
display_clockdclkDK
.nr 3brule 1
.nr 3crow 38
down_half_linehdhd
.nr 3brule 1
.nr 3crow 39
ena_acsenacseA
.nr 3brule 1
.nr 3crow 40
enter_alt_charset_modesmacsas
.nr 3brule 1
.nr 3crow 41
enter_am_modesmamSA
.nr 3brule 1
.nr 3crow 42
enter_blink_modeblinkmb
.nr 3brule 1
.nr 3crow 43
enter_bold_modeboldmd
.nr 3brule 1
.nr 3crow 44
enter_ca_modesmcupti
.nr 3brule 1
.nr 3crow 45
enter_delete_modesmdcdm
.nr 3brule 1
.nr 3crow 46
enter_dim_modedimmh
.nr 3brule 1
.nr 3crow 47
enter_doublewide_modeswidmZF
.nr 3brule 1
.nr 3crow 48
enter_draft_qualitysdrfqZG
.nr 3brule 1
.nr 3crow 49
enter_insert_modesmirim
.nr 3brule 1
.nr 3crow 50
enter_italics_modesitmZH
.nr 3brule 1
.nr 3crow 51
enter_leftward_modeslmZI
.nr 3brule 1
.nr 3crow 52
enter_micro_modesmicmZJ
.nr 3brule 1
.nr 3crow 53
enter_near_letter_qualitysnlqZK
.nr 3brule 1
.nr 3crow 54
enter_normal_qualitysnrmqZL
.nr 3brule 1
.nr 3crow 55
enter_protected_modeprotmp
.nr 3brule 1
.nr 3crow 56
enter_reverse_moderevmr
.nr 3brule 1
.nr 3crow 57
enter_secure_modeinvismk
.nr 3brule 1
.nr 3crow 58
enter_shadow_modesshmZM
.nr 3brule 1
.nr 3crow 59
enter_standout_modesmsoso
.nr 3brule 1
.nr 3crow 60
enter_subscript_modessubmZN
.nr 3brule 1
.nr 3crow 61
enter_superscript_modessupmZO
.nr 3brule 1
.nr 3crow 62
enter_underline_modesmulus
.nr 3brule 1
.nr 3crow 63
enter_upward_modesumZP
.nr 3brule 1
.nr 3crow 64
enter_xon_modesmxonSX
.nr 3brule 1
.nr 3crow 65
erase_charsechec
.nr 3brule 1
.nr 3crow 66
exit_alt_charset_modermacsae
.nr 3brule 1
.nr 3crow 67
exit_am_modermamRA
.nr 3brule 1
.nr 3crow 68
exit_attribute_modesgr0me
.nr 3brule 1
.nr 3crow 69
exit_ca_modermcupte
.nr 3brule 1
.nr 3crow 70
exit_delete_modermdced
.nr 3brule 1
.nr 3crow 71
exit_doublewide_moderwidmZQ
.nr 3brule 1
.nr 3crow 72
exit_insert_modermirei
.nr 3brule 1
.nr 3crow 73
exit_italics_moderitmZR
.nr 3brule 1
.nr 3crow 74
exit_leftward_moderlmZS
.nr 3brule 1
.nr 3crow 75
exit_micro_modermicmZT
.nr 3brule 1
.nr 3crow 76
exit_shadow_modershmZU
.nr 3brule 1
.nr 3crow 77
exit_standout_modermsose
.nr 3brule 1
.nr 3crow 78
exit_subscript_modersubmZV
.nr 3brule 1
.nr 3crow 79
exit_superscript_modersupmZW
.nr 3brule 1
.nr 3crow 80
exit_underline_modermulue
.nr 3brule 1
.nr 3crow 81
exit_upward_moderumZX
.nr 3brule 1
.nr 3crow 82
exit_xon_modermxonRX
.nr 3brule 1
.nr 3crow 83
fixed_pausepausePA
.nr 3brule 1
.nr 3crow 84
flash_hookhookfh
.nr 3brule 1
.nr 3crow 85
flash_screenflashvb
.nr 3brule 1
.nr 3crow 86
form_feedffff
.nr 3brule 1
.nr 3crow 87
from_status_linefslfs
.nr 3brule 1
.nr 3crow 88
goto_windowwingoWG
.nr 3brule 1
.nr 3crow 89
hanguphupHU
.nr 3brule 1
.nr 3crow 90
init_1stringis1i1
.nr 3brule 1
.nr 3crow 91
init_2stringis2is
.nr 3brule 1
.nr 3crow 92
init_3stringis3i3
.nr 3brule 1
.nr 3crow 93
init_fileifif
.nr 3brule 1
.nr 3crow 94
init_progiprogiP
.nr 3brule 1
.nr 3crow 95
initialize_colorinitcIc
.nr 3brule 1
.nr 3crow 96
initialize_pairinitpIp
.nr 3brule 1
.nr 3crow 97
insert_characterich1ic
.nr 3brule 1
.nr 3crow 98
insert_lineil1al
.nr 3brule 1
.nr 3crow 99
insert_paddingipip
.nr 3brule 1
.nr 3crow 100
key_a1ka1K1
.nr 3brule 1
.nr 3crow 101
key_a3ka3K3
.nr 3brule 1
.nr 3crow 102
key_b2kb2K2
.nr 3brule 1
.nr 3crow 103
key_backspacekbskb
.nr 3brule 1
.nr 3crow 104
key_begkbeg@1
.nr 3brule 1
.nr 3crow 105
key_btabkcbtkB
.nr 3brule 1
.nr 3crow 106
key_c1kc1K4
.nr 3brule 1
.nr 3crow 107
key_c3kc3K5
.nr 3brule 1
.nr 3crow 108
key_cancelkcan@2
.nr 3brule 1
.nr 3crow 109
key_catabktbcka
.nr 3brule 1
.nr 3crow 110
key_clearkclrkC
.nr 3brule 1
.nr 3crow 111
key_closekclo@3
.nr 3brule 1
.nr 3crow 112
key_commandkcmd@4
.nr 3brule 1
.nr 3crow 113
key_copykcpy@5
.nr 3brule 1
.nr 3crow 114
key_createkcrt@6
.nr 3brule 1
.nr 3crow 115
key_ctabkctabkt
.nr 3brule 1
.nr 3crow 116
key_dckdch1kD
.nr 3brule 1
.nr 3crow 117
key_dlkdl1kL
.nr 3brule 1
.nr 3crow 118
key_downkcud1kd
.nr 3brule 1
.nr 3crow 119
key_eickrmirkM
.nr 3brule 1
.nr 3crow 120
key_endkend@7
.nr 3brule 1
.nr 3crow 121
key_enterkent@8
.nr 3brule 1
.nr 3crow 122
key_eolkelkE
.nr 3brule 1
.nr 3crow 123
key_eoskedkS
.nr 3brule 1
.nr 3crow 124
key_exitkext@9
.nr 3brule 1
.nr 3crow 125
key_f0kf0k0
.nr 3brule 1
.nr 3crow 126
key_f1kf1k1
.nr 3brule 1
.nr 3crow 127
key_f10kf10k;
.nr 3brule 1
.nr 3crow 128
key_f11kf11F1
.nr 3brule 1
.nr 3crow 129
key_f12kf12F2
.nr 3brule 1
.nr 3crow 130
key_f13kf13F3
.nr 3brule 1
.nr 3crow 131
key_f14kf14F4
.nr 3brule 1
.nr 3crow 132
key_f15kf15F5
.nr 3brule 1
.nr 3crow 133
key_f16kf16F6
.nr 3brule 1
.nr 3crow 134
key_f17kf17F7
.nr 3brule 1
.nr 3crow 135
key_f18kf18F8
.nr 3brule 1
.nr 3crow 136
key_f19kf19F9
.nr 3brule 1
.nr 3crow 137
key_f2kf2k2
.nr 3brule 1
.nr 3crow 138
key_f20kf20FA
.nr 3brule 1
.nr 3crow 139
key_f21kf21FB
.nr 3brule 1
.nr 3crow 140
key_f22kf22FC
.nr 3brule 1
.nr 3crow 141
key_f23kf23FD
.nr 3brule 1
.nr 3crow 142
key_f24kf24FE
.nr 3brule 1
.nr 3crow 143
key_f25kf25FF
.nr 3brule 1
.nr 3crow 144
key_f26kf26FG
.nr 3brule 1
.nr 3crow 145
key_f27kf27FH
.nr 3brule 1
.nr 3crow 146
key_f28kf28FI
.nr 3brule 1
.nr 3crow 147
key_f29kf29FJ
.nr 3brule 1
.nr 3crow 148
key_f3kf3k3
.nr 3brule 1
.nr 3crow 149
key_f30kf30FK
.nr 3brule 1
.nr 3crow 150
key_f31kf31FL
.nr 3brule 1
.nr 3crow 151
key_f32kf32FM
.nr 3brule 1
.nr 3crow 152
key_f33kf33FN
.nr 3brule 1
.nr 3crow 153
key_f34kf34FO
.nr 3brule 1
.nr 3crow 154
key_f35kf35FP
.nr 3brule 1
.nr 3crow 155
key_f36kf36FQ
.nr 3brule 1
.nr 3crow 156
key_f37kf37FR
.nr 3brule 1
.nr 3crow 157
key_f38kf38FS
.nr 3brule 1
.nr 3crow 158
key_f39kf39FT
.nr 3brule 1
.nr 3crow 159
key_f4kf4k4
.nr 3brule 1
.nr 3crow 160
key_f40kf40FU
.nr 3brule 1
.nr 3crow 161
key_f41kf41FV
.nr 3brule 1
.nr 3crow 162
key_f42kf42FW
.nr 3brule 1
.nr 3crow 163
key_f43kf43FX
.nr 3brule 1
.nr 3crow 164
key_f44kf44FY
.nr 3brule 1
.nr 3crow 165
key_f45kf45FZ
.nr 3brule 1
.nr 3crow 166
key_f46kf46Fa
.nr 3brule 1
.nr 3crow 167
key_f47kf47Fb
.nr 3brule 1
.nr 3crow 168
key_f48kf48Fc
.nr 3brule 1
.nr 3crow 169
key_f49kf49Fd
.nr 3brule 1
.nr 3crow 170
key_f5kf5k5
.nr 3brule 1
.nr 3crow 171
key_f50kf50Fe
.nr 3brule 1
.nr 3crow 172
key_f51kf51Ff
.nr 3brule 1
.nr 3crow 173
key_f52kf52Fg
.nr 3brule 1
.nr 3crow 174
key_f53kf53Fh
.nr 3brule 1
.nr 3crow 175
key_f54kf54Fi
.nr 3brule 1
.nr 3crow 176
key_f55kf55Fj
.nr 3brule 1
.nr 3crow 177
key_f56kf56Fk
.nr 3brule 1
.nr 3crow 178
key_f57kf57Fl
.nr 3brule 1
.nr 3crow 179
key_f58kf58Fm
.nr 3brule 1
.nr 3crow 180
key_f59kf59Fn
.nr 3brule 1
.nr 3crow 181
key_f6kf6k6
.nr 3brule 1
.nr 3crow 182
key_f60kf60Fo
.nr 3brule 1
.nr 3crow 183
key_f61kf61Fp
.nr 3brule 1
.nr 3crow 184
key_f62kf62Fq
.nr 3brule 1
.nr 3crow 185
key_f63kf63Fr
.nr 3brule 1
.nr 3crow 186
key_f7kf7k7
.nr 3brule 1
.nr 3crow 187
key_f8kf8k8
.nr 3brule 1
.nr 3crow 188
key_f9kf9k9
.nr 3brule 1
.nr 3crow 189
key_findkfnd@0
.nr 3brule 1
.nr 3crow 190
key_helpkhlp%1
.nr 3brule 1
.nr 3crow 191
key_homekhomekh
.nr 3brule 1
.nr 3crow 192
key_ickich1kI
.nr 3brule 1
.nr 3crow 193
key_ilkil1kA
.nr 3brule 1
.nr 3crow 194
key_leftkcub1kl
.nr 3brule 1
.nr 3crow 195
key_llkllkH
.nr 3brule 1
.nr 3crow 196
key_markkmrk%2
.nr 3brule 1
.nr 3crow 197
key_messagekmsg%3
.nr 3brule 1
.nr 3crow 198
key_movekmov%4
.nr 3brule 1
.nr 3crow 199
key_nextknxt%5
.nr 3brule 1
.nr 3crow 200
key_npageknpkN
.nr 3brule 1
.nr 3crow 201
key_openkopn%6
.nr 3brule 1
.nr 3crow 202
key_optionskopt%7
.nr 3brule 1
.nr 3crow 203
key_ppagekppkP
.nr 3brule 1
.nr 3crow 204
key_previouskprv%8
.nr 3brule 1
.nr 3crow 205
key_printkprt%9
.nr 3brule 1
.nr 3crow 206
key_redokrdo%0
.nr 3brule 1
.nr 3crow 207
key_referencekref&1
.nr 3brule 1
.nr 3crow 208
key_refreshkrfr&2
.nr 3brule 1
.nr 3crow 209
key_replacekrpl&3
.nr 3brule 1
.nr 3crow 210
key_restartkrst&4
.nr 3brule 1
.nr 3crow 211
key_resumekres&5
.nr 3brule 1
.nr 3crow 212
key_rightkcuf1kr
.nr 3brule 1
.nr 3crow 213
key_saveksav&6
.nr 3brule 1
.nr 3crow 214
key_sbegkBEG&9
.nr 3brule 1
.nr 3crow 215
key_scancelkCAN&0
.nr 3brule 1
.nr 3crow 216
key_scommandkCMD*1
.nr 3brule 1
.nr 3crow 217
key_scopykCPY*2
.nr 3brule 1
.nr 3crow 218
key_screatekCRT*3
.nr 3brule 1
.nr 3crow 219
key_sdckDC*4
.nr 3brule 1
.nr 3crow 220
key_sdlkDL*5
.nr 3brule 1
.nr 3crow 221
key_selectkslt*6
.nr 3brule 1
.nr 3crow 222
key_sendkEND*7
.nr 3brule 1
.nr 3crow 223
key_seolkEOL*8
.nr 3brule 1
.nr 3crow 224
key_sexitkEXT*9
.nr 3brule 1
.nr 3crow 225
key_sfkindkF
.nr 3brule 1
.nr 3crow 226
key_sfindkFND*0
.nr 3brule 1
.nr 3crow 227
key_shelpkHLP#1
.nr 3brule 1
.nr 3crow 228
key_shomekHOM#2
.nr 3brule 1
.nr 3crow 229
key_sickIC#3
.nr 3brule 1
.nr 3crow 230
key_sleftkLFT#4
.nr 3brule 1
.nr 3crow 231
key_smessagekMSG%a
.nr 3brule 1
.nr 3crow 232
key_smovekMOV%b
.nr 3brule 1
.nr 3crow 233
key_snextkNXT%c
.nr 3brule 1
.nr 3crow 234
key_soptionskOPT%d
.nr 3brule 1
.nr 3crow 235
key_spreviouskPRV%e
.nr 3brule 1
.nr 3crow 236
key_sprintkPRT%f
.nr 3brule 1
.nr 3crow 237
key_srkrikR
.nr 3brule 1
.nr 3crow 238
key_sredokRDO%g
.nr 3brule 1
.nr 3crow 239
key_sreplacekRPL%h
.nr 3brule 1
.nr 3crow 240
key_srightkRIT%i
.nr 3brule 1
.nr 3crow 241
key_srsumekRES%j
.nr 3brule 1
.nr 3crow 242
key_ssavekSAV!1
.nr 3brule 1
.nr 3crow 243
key_ssuspendkSPD!2
.nr 3brule 1
.nr 3crow 244
key_stabkhtskT
.nr 3brule 1
.nr 3crow 245
key_sundokUND!3
.nr 3brule 1
.nr 3crow 246
key_suspendkspd&7
.nr 3brule 1
.nr 3crow 247
key_undokund&8
.nr 3brule 1
.nr 3crow 248
key_upkcuu1ku
.nr 3brule 1
.nr 3crow 249
keypad_localrmkxke
.nr 3brule 1
.nr 3crow 250
keypad_xmitsmkxks
.nr 3brule 1
.nr 3crow 251
lab_f0lf0l0
.nr 3brule 1
.nr 3crow 252
lab_f1lf1l1
.nr 3brule 1
.nr 3crow 253
lab_f10lf10la
.nr 3brule 1
.nr 3crow 254
lab_f2lf2l2
.nr 3brule 1
.nr 3crow 255
lab_f3lf3l3
.nr 3brule 1
.nr 3crow 256
lab_f4lf4l4
.nr 3brule 1
.nr 3crow 257
lab_f5lf5l5
.nr 3brule 1
.nr 3crow 258
lab_f6lf6l6
.nr 3brule 1
.nr 3crow 259
lab_f7lf7l7
.nr 3brule 1
.nr 3crow 260
lab_f8lf8l8
.nr 3brule 1
.nr 3crow 261
lab_f9lf9l9
.nr 3brule 1
.nr 3crow 262
label_formatflnLf
.nr 3brule 1
.nr 3crow 263
label_offrmlnLF
.nr 3brule 1
.nr 3crow 264
label_onsmlnLO
.nr 3brule 1
.nr 3crow 265
meta_offrmmmo
.nr 3brule 1
.nr 3crow 266
meta_onsmmmm
.nr 3brule 1
.nr 3crow 267
micro_column_addressmhpaZY
.nr 3brule 1
.nr 3crow 268
micro_downmcud1ZZ
.nr 3brule 1
.nr 3crow 269
micro_leftmcub1Za
.nr 3brule 1
.nr 3crow 270
micro_rightmcuf1Zb
.nr 3brule 1
.nr 3crow 271
micro_row_addressmvpaZc
.nr 3brule 1
.nr 3crow 272
micro_upmcuu1Zd
.nr 3brule 1
.nr 3crow 273
newlinenelnw
.nr 3brule 1
.nr 3crow 274
order_of_pinsporderZe
.nr 3brule 1
.nr 3crow 275
orig_colorsococ
.nr 3brule 1
.nr 3crow 276
orig_pairopop
.nr 3brule 1
.nr 3crow 277
pad_charpadpc
.nr 3brule 1
.nr 3crow 278
parm_dchdchDC
.nr 3brule 1
.nr 3crow 279
parm_delete_linedlDL
.nr 3brule 1
.nr 3crow 280
parm_down_cursorcudDO
.nr 3brule 1
.nr 3crow 281
parm_down_micromcudZf
.nr 3brule 1
.nr 3crow 282
parm_ichichIC
.nr 3brule 1
.nr 3crow 283
parm_indexindnSF
.nr 3brule 1
.nr 3crow 284
parm_insert_lineilAL
.nr 3brule 1
.nr 3crow 285
parm_left_cursorcubLE
.nr 3brule 1
.nr 3crow 286
parm_left_micromcubZg
.nr 3brule 1
.nr 3crow 287
parm_right_cursorcufRI
.nr 3brule 1
.nr 3crow 288
parm_right_micromcufZh
.nr 3brule 1
.nr 3crow 289
parm_rindexrinSR
.nr 3brule 1
.nr 3crow 290
parm_up_cursorcuuUP
.nr 3brule 1
.nr 3crow 291
parm_up_micromcuuZi
.nr 3brule 1
.nr 3crow 292
pkey_keypfkeypk
.nr 3brule 1
.nr 3crow 293
pkey_localpflocpl
.nr 3brule 1
.nr 3crow 294
pkey_xmitpfxpx
.nr 3brule 1
.nr 3crow 295
plab_normplnpn
.nr 3brule 1
.nr 3crow 296
print_screenmc0ps
.nr 3brule 1
.nr 3crow 297
prtr_nonmc5ppO
.nr 3brule 1
.nr 3crow 298
prtr_offmc4pf
.nr 3brule 1
.nr 3crow 299
prtr_onmc5po
.nr 3brule 1
.nr 3crow 300
pulsepulsePU
.nr 3brule 1
.nr 3crow 301
quick_dialqdialQD
.nr 3brule 1
.nr 3crow 302
remove_clockrmclkRC
.nr 3brule 1
.nr 3crow 303
repeat_charreprp
.nr 3brule 1
.nr 3crow 304
req_for_inputrfiRF
.nr 3brule 1
.nr 3crow 305
reset_1stringrs1r1
.nr 3brule 1
.nr 3crow 306
reset_2stringrs2r2
.nr 3brule 1
.nr 3crow 307
reset_3stringrs3r3
.nr 3brule 1
.nr 3crow 308
reset_filerfrf
.nr 3brule 1
.nr 3crow 309
restore_cursorrcrc
.nr 3brule 1
.nr 3crow 310
row_addressvpacv
.nr 3brule 1
.nr 3crow 311
save_cursorscsc
.nr 3brule 1
.nr 3crow 312
scroll_forwardindsf
.nr 3brule 1
.nr 3crow 313
scroll_reverserisr
.nr 3brule 1
.nr 3crow 314
select_char_setscsZj
.nr 3brule 1
.nr 3crow 315
set_attributessgrsa
.nr 3brule 1
.nr 3crow 316
set_backgroundsetbSb
.nr 3brule 1
.nr 3crow 317
set_bottom_marginsmgbZk
.nr 3brule 1
.nr 3crow 318
set_bottom_margin_parmsmgbpZl
.nr 3brule 1
.nr 3crow 319
set_clocksclkSC
.nr 3brule 1
.nr 3crow 320
set_color_pairscpsp
.nr 3brule 1
.nr 3crow 321
set_foregroundsetfSf
.nr 3brule 1
.nr 3crow 322
set_left_marginsmglML
.nr 3brule 1
.nr 3crow 323
set_left_margin_parmsmglpZm
.nr 3brule 1
.nr 3crow 324
set_right_marginsmgrMR
.nr 3brule 1
.nr 3crow 325
set_right_margin_parmsmgrpZn
.nr 3brule 1
.nr 3crow 326
set_tabhtsst
.nr 3brule 1
.nr 3crow 327
set_top_marginsmgtZo
.nr 3brule 1
.nr 3crow 328
set_top_margin_parmsmgtpZp
.nr 3brule 1
.nr 3crow 329
set_windowwindwi
.nr 3brule 1
.nr 3crow 330
start_bit_imagesbimZq
.nr 3brule 1
.nr 3crow 331
start_char_set_defscsdZr
.nr 3brule 1
.nr 3crow 332
stop_bit_imagerbimZs
.nr 3brule 1
.nr 3crow 333
stop_char_set_defrcsdZt
.nr 3brule 1
.nr 3crow 334
subscript_characterssubcsZu
.nr 3brule 1
.nr 3crow 335
superscript_characterssupcsZv
.nr 3brule 1
.nr 3crow 336
tabhtta
.nr 3brule 1
.nr 3crow 337
these_cause_crdocrZw
.nr 3brule 1
.nr 3crow 338
to_status_linetslts
.nr 3brule 1
.nr 3crow 339
tonetoneTO
.nr 3brule 1
.nr 3crow 340
underline_charucuc
.nr 3brule 1
.nr 3crow 341
up_half_linehuhu
.nr 3brule 1
.nr 3crow 342
user0u0u0
.nr 3brule 1
.nr 3crow 343
user1u1u1
.nr 3brule 1
.nr 3crow 344
user2u2u2
.nr 3brule 1
.nr 3crow 345
user3u3u3
.nr 3brule 1
.nr 3crow 346
user4u4u4
.nr 3brule 1
.nr 3crow 347
user5u5u5
.nr 3brule 1
.nr 3crow 348
user6u6u6
.nr 3brule 1
.nr 3crow 349
user7u7u7
.nr 3brule 1
.nr 3crow 350
user8u8u8
.nr 3brule 1
.nr 3crow 351
user9u9u9
.nr 3brule 1
.nr 3crow 352
wait_tonewaitWA
.nr 3brule 1
.nr 3crow 353
xoff_characterxoffcXF
.nr 3brule 1
.nr 3crow 354
xon_characterxoncXN
.nr 3brule 1
.nr 3crow 355
zero_motionzeromZx
.nr 3brule 1
The following string capabilities are present in the SVr4.0 term structure, but were originally not documented in the man page.
Mouse event has occurred
Mouse status information
PC terminal options
Program function key #1 to type string #2 and show string #3
Request mouse position
Escape for scancode emulation
Shift to codeset 0 (EUC set 0, ASCII)
Shift to codeset 1
Shift to codeset 2
Shift to codeset 3
Set background color to #1, using ANSI escape
Set foreground color to #1, using ANSI escape
Change to ribbon color #1
Set both left and right margins to #1, #2. (ML is not in BSD termcap).
Set page length to #1 lines
Sets both top and bottom margins to #1, #2
.nr 3crow 0
VariableCap-TCapDescription
.nr 3brule 1
.nr 3crow 1
StringnameCode
.nr 3brule 1
.nr 3crow 2
alt_scancode_escscesaS8
.nr 3brule 1
.nr 3crow 3
bit_image_carriage_returnbicrYv
.nr 3brule 1
.nr 3crow 4
bit_image_newlinebinelZz
.nr 3brule 1
.nr 3crow 5
bit_image_repeatbirepXy
.nr 3brule 1
.nr 3crow 6
char_set_namescsnmZy
.nr 3brule 1
.nr 3crow 7
code_set_initcsinci
.nr 3brule 1
.nr 3crow 8
color_namescolornmYw
.nr 3brule 1
.nr 3crow 9
define_bit_image_regiondefbiYx
.nr 3brule 1
.nr 3crow 10
device_typedevtdv
.nr 3brule 1
.nr 3crow 11
display_pc_chardispcS1
.nr 3brule 1
.nr 3crow 12
end_bit_image_regionendbiYy
.nr 3brule 1
.nr 3crow 13
enter_pc_charset_modesmpchS2
.nr 3brule 1
.nr 3crow 14
enter_scancode_modesmscS4
.nr 3brule 1
.nr 3crow 15
exit_pc_charset_modermpchS3
.nr 3brule 1
.nr 3crow 16
exit_scancode_modermscS5
.nr 3brule 1
.nr 3crow 17
get_mousegetmGm
.nr 3brule 1
.nr 3crow 18
key_mousekmousKm
.nr 3brule 1
.nr 3crow 19
mouse_infominfoMi
.nr 3brule 1
.nr 3crow 20
pc_term_optionspctrmS6
.nr 3brule 1
.nr 3crow 21
pkey_plabpfxlxl
.nr 3brule 1
.nr 3crow 22
req_mouse_posreqmpRQ
.nr 3brule 1
.nr 3crow 23
scancode_escapescescS7
.nr 3brule 1
.nr 3crow 24
set0_des_seqs0dss0
.nr 3brule 1
.nr 3crow 25
set1_des_seqs1dss1
.nr 3brule 1
.nr 3crow 26
set2_des_seqs2dss2
.nr 3brule 1
.nr 3crow 27
set3_des_seqs3dss3
.nr 3brule 1
.nr 3crow 28
set_a_backgroundsetabAB
.nr 3brule 1
.nr 3crow 29
set_a_foregroundsetafAF
.nr 3brule 1
.nr 3crow 30
set_color_bandsetcolorYz
.nr 3brule 1
.nr 3crow 31
set_lr_marginsmglrML
.nr 3brule 1
.nr 3crow 32
set_page_lengthslinesYZ
.nr 3brule 1
.nr 3crow 33
set_tb_marginsmgtbMT
.nr 3brule 1
The XSI Curses standard added these. They are some post-4.1 versions of System V curses, e.g., Solaris 2.5 and IRIX 6.x. The ncurses termcap names for them are invented; according to the XSI Curses standard, they have no termcap names. If your compiled terminfo entries use these, they may not be binary-compatible with System V terminfo entries after SVr4.1; beware!

  A Sample Entry
The following entry, describing an ANSI-standard terminal, is representative of what a terminfo entry for a modern terminal typically looks like.

ansi|ansi/pc-term compatible with color,
        mc5i,
        colors#8, ncv#3, pairs#64,
        cub=\E[%p1%dD, cud=\E[%p1%dB, cuf=\E[%p1%dC,
        cuu=\E[%p1%dA, dch=\E[%p1%dP, dl=\E[%p1%dM,
        ech=\E[%p1%dX, el1=\E[1K, hpa=\E[%p1%dG, ht=\E[I,
        ich=\E[%p1%d@, il=\E[%p1%dL, indn=\E[%p1%dS, .indn=\E[%p1%dT,
        kbs=^H, kcbt=\E[Z, kcub1=\E[D, kcud1=\E[B,
        kcuf1=\E[C, kcuu1=\E[A, kf1=\E[M, kf10=\E[V,
        kf11=\E[W, kf12=\E[X, kf2=\E[N, kf3=\E[O, kf4=\E[P,
        kf5=\E[Q, kf6=\E[R, kf7=\E[S, kf8=\E[T, kf9=\E[U,
        kich1=\E[L, mc4=\E[4i, mc5=\E[5i, nel=\r\E[S,
        op=\E[37;40m, rep=%p1%c\E[%p2%{1}%-%db,
        rin=\E[%p1%dT, s0ds=\E(B, s1ds=\E)B, s2ds=\E*B,
        s3ds=\E+B, setab=\E[4%p1%dm, setaf=\E[3%p1%dm,
        setb=\E[4%?%p1%{1}%=%t4%e%p1%{3}%=%t6%e%p1%{4}%=%t1%e%p1%{6}%=%t3%e%p1%d%;m,
        setf=\E[3%?%p1%{1}%=%t4%e%p1%{3}%=%t6%e%p1%{4}%=%t1%e%p1%{6}%=%t3%e%p1%d%;m,
        sgr=\E[0;10%?%p1%t;7%;%?%p2%t;4%;%?%p3%t;7%;%?%p4%t;5%;%?%p6%t;1%;%?%p7%t;8%;%?%p8%t;11%;%?%p9%t;12%;m,
        sgr0=\E[0;10m, tbc=\E[2g, u6=\E[%d;%dR, u7=\E[6n,
        u8=\E[?%[;0123456789]c, u9=\E[c, vpa=\E[%p1%dd,

Entries may continue onto multiple lines by placing white space at the beginning of each line except the first. Comments may be included on lines beginning with ``#''. Capabilities in terminfo are of three types: Boolean capabilities which indicate that the terminal has some particular feature, numeric capabilities giving the size of the terminal or the size of particular delays, and string capabilities, which give a sequence which can be used to perform particular terminal operations.

  Types of Capabilities

All capabilities have names. For instance, the fact that ANSI-standard terminals have automatic margins (i.e., an automatic return and line-feed when the end of a line is reached) is indicated by the capability am. Hence the description of ansi includes am. Numeric capabilities are followed by the character `#' and then a positive value. Thus cols, which indicates the number of columns the terminal has, gives the value `80' for ansi. Values for numeric capabilities may be specified in decimal, octal or hexadecimal, using the C programming language conventions (e.g., 255, 0377 and 0xff or 0xFF).

Finally, string valued capabilities, such as el (clear to end of line sequence) are given by the two-character code, an `=', and then a string ending at the next following `,'.

A number of escape sequences are provided in the string valued capabilities for easy encoding of characters there. Both \E and \e map to an ESCAPE character, ^x maps to a control-x for any appropriate x, and the sequences \n \l \r \t \b \f \s give a newline, line-feed, return, tab, backspace, form-feed, and space. Other escapes include \^ for ^, \\ for \, \, for comma, \: for :, and \0 for null. (\0 will produce \200, which does not terminate a string but behaves as a null character on most terminals, providing CS7 is specified. See stty(1).) Finally, characters may be given as three octal digits after a \.

A delay in milliseconds may appear anywhere in a string capability, enclosed in $<..> brackets, as in el=\EK$<5>, and padding characters are supplied by tputs to provide this delay. The delay must be a number with at most one decimal place of precision; it may be followed by suffixes `*' or '/' or both. A `*' indicates that the padding required is proportional to the number of lines affected by the operation, and the amount given is the per-affected-unit padding required. (In the case of insert character, the factor is still the number of lines affected.) Normally, padding is advisory if the device has the xon capability; it is used for cost computation but does not trigger delays. A `/' suffix indicates that the padding is mandatory and forces a delay of the given number of milliseconds even on devices for which xon is present to indicate flow control.

Sometimes individual capabilities must be commented out. To do this, put a period before the capability name. For example, see the second ind in the example above.

  Fetching Compiled Descriptions

If the environment variable TERMINFO is set, it is interpreted as the pathname of a directory containing the compiled description you are working on. Only that directory is searched.

If TERMINFO is not set, the ncurses version of the terminfo reader code will instead look in the directory $HOME/.terminfo for a compiled description. If it fails to find one there, and the environment variable TERMINFO_DIRS is set, it will interpret the contents of that variable as a list of colon- separated directories to be searched (an empty entry is interpreted as a command to search /usr/pkg/share/terminfo). If no description is found in any of the TERMINFO_DIRS directories, the fetch fails.

If neither TERMINFO nor TERMINFO_DIRS is set, the last place tried will be the system terminfo directory, /usr/pkg/share/terminfo.

(Neither the $HOME/.terminfo lookups nor TERMINFO_DIRS extensions are supported under stock System V terminfo/curses.)

  Preparing Descriptions

We now outline how to prepare descriptions of terminals. The most effective way to prepare a terminal description is by imitating the description of a similar terminal in terminfo and to build up a description gradually, using partial descriptions with vi or some other screen-oriented program to check that they are correct. Be aware that a very unusual terminal may expose deficiencies in the ability of the terminfo file to describe it or bugs in the screen-handling code of the test program.

To get the padding for insert line right (if the terminal manufacturer did not document it) a severe test is to edit a large file at 9600 baud, delete 16 or so lines from the middle of the screen, then hit the `u' key several times quickly. If the terminal messes up, more padding is usually needed. A similar test can be used for insert character.

  Basic Capabilities

The number of columns on each line for the terminal is given by the cols numeric capability. If the terminal is a CRT, then the number of lines on the screen is given by the lines capability. If the terminal wraps around to the beginning of the next line when it reaches the right margin, then it should have the am capability. If the terminal can clear its screen, leaving the cursor in the home position, then this is given by the clear string capability. If the terminal overstrikes (rather than clearing a position when a character is struck over) then it should have the os capability. If the terminal is a printing terminal, with no soft copy unit, give it both hc and os. (os applies to storage scope terminals, such as TEKTRONIX 4010 series, as well as hard copy and APL terminals.) If there is a code to move the cursor to the left edge of the current row, give this as cr. (Normally this will be carriage return, control M.) If there is a code to produce an audible signal (bell, beep, etc) give this as bel.

If there is a code to move the cursor one position to the left (such as backspace) that capability should be given as cub1. Similarly, codes to move to the right, up, and down should be given as cuf1, cuu1, and cud1. These local cursor motions should not alter the text they pass over, for example, you would not normally use `cuf1= ' because the space would erase the character moved over.

A very important point here is that the local cursor motions encoded in terminfo are undefined at the left and top edges of a CRT terminal. Programs should never attempt to backspace around the left edge, unless bw is given, and never attempt to go up locally off the top. In order to scroll text up, a program will go to the bottom left corner of the screen and send the ind (index) string.

To scroll text down, a program goes to the top left corner of the screen and sends the ri (reverse index) string. The strings ind and ri are undefined when not on their respective corners of the screen.

Parameterized versions of the scrolling sequences are indn and rin which have the same semantics as ind and ri except that they take one parameter, and scroll that many lines. They are also undefined except at the appropriate edge of the screen.

The am capability tells whether the cursor sticks at the right edge of the screen when text is output, but this does not necessarily apply to a cuf1 from the last column. The only local motion which is defined from the left edge is if bw is given, then a cub1 from the left edge will move to the right edge of the previous row. If bw is not given, the effect is undefined. This is useful for drawing a box around the edge of the screen, for example. If the terminal has switch selectable automatic margins, the terminfo file usually assumes that this is on; i.e., am. If the terminal has a command which moves to the first column of the next line, that command can be given as nel (newline). It does not matter if the command clears the remainder of the current line, so if the terminal has no cr and lf it may still be possible to craft a working nel out of one or both of them.

These capabilities suffice to describe hard-copy and “glass-tty” terminals. Thus the model 33 teletype is described as

3|tty33|tty|model 33 teletype,
	bel=^G, cols#72, cr=^M, cud1=^J, hc, ind=^J, os,

while the Lear Siegler ADM-3 is described as

adm3|3|lsi adm3,
	am, bel=^G, clear=^Z, cols#80, cr=^M, cub1=^H, cud1=^J,
	ind=^J, lines#24,

  Parameterized Strings

Cursor addressing and other strings requiring parameters in the terminal are described by a parameterized string capability, with printf(3) like escapes %x in it. For example, to address the cursor, the cup capability is given, using two parameters: the row and column to address to. (Rows and columns are numbered from zero and refer to the physical screen visible to the user, not to any unseen memory.) If the terminal has memory relative cursor addressing, that can be indicated by mrcup.

The parameter mechanism uses a stack and special % codes to manipulate it. Typically a sequence will push one of the parameters onto the stack and then print it in some format. Print (e.g., "%d") is a special case. Other operations, including "%t" pop their operand from the stack. It is noted that more complex operations are often necessary, e.g., in the sgr string.

The % encodings have the following meanings:

%%  outputs `%'

%[[:]flags][width[.precision]][doxXs]
    as in printf, flags are [-+#] and space. Use a `:' to allow the next character to be a `-' flag, avoiding interpreting "%-" as an operator.

%c  print pop() like %c in printf

%s  print pop() like %s in printf

%p[1-9]
    push i'th parameter

%P[a-z]
    set dynamic variable [a-z] to pop()

%g[a-z]
    get dynamic variable [a-z] and push it

%P[A-Z]
    set static variable [a-z] to pop()

%g[A-Z]
    get static variable [a-z] and push it

    The terms "static" and "dynamic" are misleading. Historically, these are simply two different sets of variables, whose values are not reset between calls to tparm. However, that fact is not documented in other implementations. Relying on it will adversely impact portability to other implementations.

%'c'
    char constant c

%{nn}
    integer constant nn

%l  push strlen(pop)

%+ %- %* %/ %m
    arithmetic (%m is mod): push(pop() op pop())

%& %| %^
    bit operations (AND, OR and exclusive-OR): push(pop() op pop())

%= %> %<
    logical operations: push(pop() op pop())

%A, %O
    logical AND and OR operations (for conditionals)

%! %~
    unary operations (logical and bit complement): push(op pop())

%i  add 1 to first two parameters (for ANSI terminals)

%? expr %t thenpart %e elsepart %;
    This forms an if-then-else. The %e elsepart is optional. Usually the %? expr part pushes a value onto the stack, and %t pops it from the stack, testing if it is nonzero (true). If it is zero (false), control passes to the %e (else) part.

    It is possible to form else-if's a la Algol 68:
    %? c1 %t b1 %e c2 %t b2 %e c3 %t b3 %e c4 %t b4 %e %;

    where ci are conditions, bi are bodies.

    Use the -f option of tic or infocmp to see the structure of if-then-else's. Some strings, e.g., sgr can be very complicated when written on one line. The -f option splits the string into lines with the parts indented.

Binary operations are in postfix form with the operands in the usual order. That is, to get x-5 one would use "%gx%{5}%-". %P and %g variables are persistent across escape-string evaluations.

Consider the HP2645, which, to get to row 3 and column 12, needs to be sent \E&a12c03Y padded for 6 milliseconds. Note that the order of the rows and columns is inverted here, and that the row and column are printed as two digits. Thus its cup capability is “cup=6\E&%p2%2dc%p1%2dY”.

The Microterm ACT-IV needs the current row and column sent preceded by a ^T, with the row and column simply encoded in binary, “cup=^T%p1%c%p2%c”. Terminals which use “%c” need to be able to backspace the cursor (cub1), and to move the cursor up one line on the screen (cuu1). This is necessary because it is not always safe to transmit \n ^D and \r, as the system may change or discard them. (The library routines dealing with terminfo set tty modes so that tabs are never expanded, so \t is safe to send. This turns out to be essential for the Ann Arbor 4080.)

A final example is the LSI ADM-3a, which uses row and column offset by a blank character, thus “cup=\E=%p1%' '%+%c%p2%' '%+%c”. After sending `\E=', this pushes the first parameter, pushes the ASCII value for a space (32), adds them (pushing the sum on the stack in place of the two previous values) and outputs that value as a character. Then the same is done for the second parameter. More complex arithmetic is possible using the stack.

  Cursor Motions

If the terminal has a fast way to home the cursor (to very upper left corner of screen) then this can be given as home; similarly a fast way of getting to the lower left-hand corner can be given as ll; this may involve going up with cuu1 from the home position, but a program should never do this itself (unless ll does) because it can make no assumption about the effect of moving up from the home position. Note that the home position is the same as addressing to (0,0): to the top left corner of the screen, not of memory. (Thus, the \EH sequence on HP terminals cannot be used for home.)

If the terminal has row or column absolute cursor addressing, these can be given as single parameter capabilities hpa (horizontal position absolute) and vpa (vertical position absolute). Sometimes these are shorter than the more general two parameter sequence (as with the hp2645) and can be used in preference to cup. If there are parameterized local motions (e.g., move n spaces to the right) these can be given as cud, cub, cuf, and cuu with a single parameter indicating how many spaces to move. These are primarily useful if the terminal does not have cup, such as the TEKTRONIX 4025.

If the terminal needs to be in a special mode when running a program that uses these capabilities, the codes to enter and exit this mode can be given as smcup and rmcup. This arises, for example, from terminals like the Concept with more than one page of memory. If the terminal has only memory relative cursor addressing and not screen relative cursor addressing, a one screen-sized window must be fixed into the terminal for cursor addressing to work properly. This is also used for the TEKTRONIX 4025, where smcup sets the command character to be the one used by terminfo. If the smcup sequence will not restore the screen after an rmcup sequence is output (to the state prior to outputting rmcup), specify nrrmc.

  Area Clears

If the terminal can clear from the current position to the end of the line, leaving the cursor where it is, this should be given as el. If the terminal can clear from the beginning of the line to the current position inclusive, leaving the cursor where it is, this should be given as el1. If the terminal can clear from the current position to the end of the display, then this should be given as ed. Ed is only defined from the first column of a line. (Thus, it can be simulated by a request to delete a large number of lines, if a true ed is not available.)

  Insert/delete line and vertical motions

If the terminal can open a new blank line before the line where the cursor is, this should be given as il1; this is done only from the first position of a line. The cursor must then appear on the newly blank line. If the terminal can delete the line which the cursor is on, then this should be given as dl1; this is done only from the first position on the line to be deleted. Versions of il1 and dl1 which take a single parameter and insert or delete that many lines can be given as il and dl.

If the terminal has a settable scrolling region (like the vt100) the command to set this can be described with the csr capability, which takes two parameters: the top and bottom lines of the scrolling region. The cursor position is, alas, undefined after using this command.

It is possible to get the effect of insert or delete line using csr on a properly chosen region; the sc and rc (save and restore cursor) commands may be useful for ensuring that your synthesized insert/delete string does not move the cursor. (Note that the ncurses(3X) library does this synthesis automatically, so you need not compose insert/delete strings for an entry with csr).

Yet another way to construct insert and delete might be to use a combination of index with the memory-lock feature found on some terminals (like the HP-700/90 series, which however also has insert/delete).

Inserting lines at the top or bottom of the screen can also be done using ri or ind on many terminals without a true insert/delete line, and is often faster even on terminals with those features.

The boolean non_dest_scroll_region should be set if each scrolling window is effectively a view port on a screen-sized canvas. To test for this capability, create a scrolling region in the middle of the screen, write something to the bottom line, move the cursor to the top of the region, and do ri followed by dl1 or ind. If the data scrolled off the bottom of the region by the ri re-appears, then scrolling is non-destructive. System V and XSI Curses expect that ind, ri, indn, and rin will simulate destructive scrolling; their documentation cautions you not to define csr unless this is true. This curses implementation is more liberal and will do explicit erases after scrolling if ndstr is defined.

If the terminal has the ability to define a window as part of memory, which all commands affect, it should be given as the parameterized string wind. The four parameters are the starting and ending lines in memory and the starting and ending columns in memory, in that order.

If the terminal can retain display memory above, then the da capability should be given; if display memory can be retained below, then db should be given. These indicate that deleting a line or scrolling may bring non-blank lines up from below or that scrolling back with ri may bring down non-blank lines.

  Insert/Delete Character

There are two basic kinds of intelligent terminals with respect to insert/delete character which can be described using terminfo. The most common insert/delete character operations affect only the characters on the current line and shift characters off the end of the line rigidly. Other terminals, such as the Concept 100 and the Perkin Elmer Owl, make a distinction between typed and untyped blanks on the screen, shifting upon an insert or delete only to an untyped blank on the screen which is either eliminated, or expanded to two untyped blanks. You can determine the kind of terminal you have by clearing the screen and then typing text separated by cursor motions. Type “abc def” using local cursor motions (not spaces) between the “abc” and the “def”. Then position the cursor before the “abc” and put the terminal in insert mode. If typing characters causes the rest of the line to shift rigidly and characters to fall off the end, then your terminal does not distinguish between blanks and untyped positions. If the “abc” shifts over to the “def” which then move together around the end of the current line and onto the next as you insert, you have the second type of terminal, and should give the capability in, which stands for “insert null”. While these are two logically separate attributes (one line versus multi-line insert mode, and special treatment of untyped spaces) we have seen no terminals whose insert mode cannot be described with the single attribute.

Terminfo can describe both terminals which have an insert mode, and terminals which send a simple sequence to open a blank position on the current line. Give as smir the sequence to get into insert mode. Give as rmir the sequence to leave insert mode. Now give as ich1 any sequence needed to be sent just before sending the character to be inserted. Most terminals with a true insert mode will not give ich1; terminals which send a sequence to open a screen position should give it here.

If your terminal has both, insert mode is usually preferable to ich1. Technically, you should not give both unless the terminal actually requires both to be used in combination. Accordingly, some non-curses applications get confused if both are present; the symptom is doubled characters in an update using insert. This requirement is now rare; most ich sequences do not require previous smir, and most smir insert modes do not require ich1 before each character. Therefore, the new curses actually assumes this is the case and uses either rmir/smir or ich/ich1 as appropriate (but not both). If you have to write an entry to be used under new curses for a terminal old enough to need both, include the rmir/smir sequences in ich1.

If post insert padding is needed, give this as a number of milliseconds in ip (a string option). Any other sequence which may need to be sent after an insert of a single character may also be given in ip. If your terminal needs both to be placed into an `insert mode' and a special code to precede each inserted character, then both smir/rmir and ich1 can be given, and both will be used. The ich capability, with one parameter, n, will repeat the effects of ich1 n times.

If padding is necessary between characters typed while not in insert mode, give this as a number of milliseconds padding in rmp.

It is occasionally necessary to move around while in insert mode to delete characters on the same line (e.g., if there is a tab after the insertion position). If your terminal allows motion while in insert mode you can give the capability mir to speed up inserting in this case. Omitting mir will affect only speed. Some terminals (notably Datamedia's) must not have mir because of the way their insert mode works.

Finally, you can specify dch1 to delete a single character, dch with one parameter, n, to delete n characters, and delete mode by giving smdc and rmdc to enter and exit delete mode (any mode the terminal needs to be placed in for dch1 to work).

A command to erase n characters (equivalent to outputting n blanks without moving the cursor) can be given as ech with one parameter.

  Highlighting, Underlining, and Visible Bells

If your terminal has one or more kinds of display attributes, these can be represented in a number of different ways. You should choose one display form as standout mode, representing a good, high contrast, easy-on-the-eyes, format for highlighting error messages and other attention getters. (If you have a choice, reverse video plus half-bright is good, or reverse video alone.) The sequences to enter and exit standout mode are given as smso and rmso, respectively. If the code to change into or out of standout mode leaves one or even two blank spaces on the screen, as the TVI 912 and Teleray 1061 do, then xmc should be given to tell how many spaces are left.

Codes to begin underlining and end underlining can be given as smul and rmul respectively. If the terminal has a code to underline the current character and move the cursor one space to the right, such as the Microterm Mime, this can be given as uc.

Other capabilities to enter various highlighting modes include blink (blinking) bold (bold or extra bright) dim (dim or half-bright) invis (blanking or invisible text) prot (protected) rev (reverse video) sgr0 (turn off all attribute modes) smacs (enter alternate character set mode) and rmacs (exit alternate character set mode). Turning on any of these modes singly may or may not turn off other modes.

If there is a sequence to set arbitrary combinations of modes, this should be given as sgr (set attributes), taking 9 parameters. Each parameter is either 0 or nonzero, as the corresponding attribute is on or off. The 9 parameters are, in order: standout, underline, reverse, blink, dim, bold, blank, protect, alternate character set. Not all modes need be supported by sgr, only those for which corresponding separate attribute commands exist.

For example, the DEC vt220 supports most of the modes:

We begin each escape sequence by turning off any existing modes, since there is no quick way to determine whether they are active. Standout is set up to be the combination of reverse and bold. The vt220 terminal has a protect mode, though it is not commonly used in sgr because it protects characters on the screen from the host's erasures. The altcharset mode also is different in that it is either ^O or ^N, depending on whether it is off or on. If all modes are turned on, the resulting sequence is \E[0;1;4;5;7;8m^N.

Some sequences are common to different modes. For example, ;7 is output when either p1 or p3 is true, that is, if either standout or reverse modes are turned on.

Writing out the above sequences, along with their dependencies yields

Putting this all together into the sgr sequence gives:

    sgr=\E[0%?%p1%p6%|%t;1%;%?%p2%t;4%;%?%p1%p3%|%t;7%;
        %?%p4%t;5%;%?%p7%t;8%;m%?%p9%t\016%e\017%;,

Remember that if you specify sgr, you must also specify sgr0. Also, some implementations rely on sgr being given if sgr0 is, Not all terminfo entries necessarily have an sgr string, however. Many terminfo entries are derived from termcap entries which have no sgr string. The only drawback to adding an sgr string is that termcap also assumes that sgr0 does not exit alternate character set mode.

Terminals with the ``magic cookie'' glitch (xmc) deposit special ``cookies'' when they receive mode-setting sequences, which affect the display algorithm rather than having extra bits for each character. Some terminals, such as the HP 2621, automatically leave standout mode when they move to a new line or the cursor is addressed. Programs using standout mode should exit standout mode before moving the cursor or sending a newline, unless the msgr capability, asserting that it is safe to move in standout mode, is present.

If the terminal has a way of flashing the screen to indicate an error quietly (a bell replacement) then this can be given as flash; it must not move the cursor.

If the cursor needs to be made more visible than normal when it is not on the bottom line (to make, for example, a non-blinking underline into an easier to find block or blinking underline) give this sequence as cvvis. If there is a way to make the cursor completely invisible, give that as civis. The capability cnorm should be given which undoes the effects of both of these modes.

If your terminal correctly generates underlined characters (with no special codes needed) even though it does not overstrike, then you should give the capability ul. If a character overstriking another leaves both characters on the screen, specify the capability os. If overstrikes are erasable with a blank, then this should be indicated by giving eo.

  Keypad and Function Keys

If the terminal has a keypad that transmits codes when the keys are pressed, this information can be given. Note that it is not possible to handle terminals where the keypad only works in local (this applies, for example, to the unshifted HP 2621 keys). If the keypad can be set to transmit or not transmit, give these codes as smkx and rmkx. Otherwise the keypad is assumed to always transmit. The codes sent by the left arrow, right arrow, up arrow, down arrow, and home keys can be given as kcub1, kcuf1, kcuu1, kcud1, and khome respectively. If there are function keys such as f0, f1, ..., f10, the codes they send can be given as kf0, kf1, ..., kf10. If these keys have labels other than the default f0 through f10, the labels can be given as lf0, lf1, ..., lf10. The codes transmitted by certain other special keys can be given: kll (home down), kbs (backspace), ktbc (clear all tabs), kctab (clear the tab stop in this column), kclr (clear screen or erase key), kdch1 (delete character), kdl1 (delete line), krmir (exit insert mode), kel (clear to end of line), ked (clear to end of screen), kich1 (insert character or enter insert mode), kil1 (insert line), knp (next page), kpp (previous page), kind (scroll forward/down), kri (scroll backward/up), khts (set a tab stop in this column). In addition, if the keypad has a 3 by 3 array of keys including the four arrow keys, the other five keys can be given as ka1, ka3, kb2, kc1, and kc3. These keys are useful when the effects of a 3 by 3 directional pad are needed.

Strings to program function keys can be given as pfkey, pfloc, and pfx. A string to program screen labels should be specified as pln. Each of these strings takes two parameters: the function key number to program (from 0 to 10) and the string to program it with. Function key numbers out of this range may program undefined keys in a terminal dependent manner. The difference between the capabilities is that pfkey causes pressing the given key to be the same as the user typing the given string; pfloc causes the string to be executed by the terminal in local; and pfx causes the string to be transmitted to the computer.

The capabilities nlab, lw and lh define the number of programmable screen labels and their width and height. If there are commands to turn the labels on and off, give them in smln and rmln. smln is normally output after one or more pln sequences to make sure that the change becomes visible.

  Tabs and Initialization

If the terminal has hardware tabs, the command to advance to the next tab stop can be given as ht (usually control I). A ``back-tab'' command which moves leftward to the preceding tab stop can be given as cbt. By convention, if the teletype modes indicate that tabs are being expanded by the computer rather than being sent to the terminal, programs should not use ht or cbt even if they are present, since the user may not have the tab stops properly set. If the terminal has hardware tabs which are initially set every n spaces when the terminal is powered up, the numeric parameter it is given, showing the number of spaces the tabs are set to. This is normally used by the tset command to determine whether to set the mode for hardware tab expansion, and whether to set the tab stops. If the terminal has tab stops that can be saved in non-volatile memory, the terminfo description can assume that they are properly set.

Other capabilities include is1, is2, and is3, initialization strings for the terminal, iprog, the path name of a program to be run to initialize the terminal, and if, the name of a file containing long initialization strings. These strings are expected to set the terminal into modes consistent with the rest of the terminfo description. They are normally sent to the terminal, by the init option of the tput program, each time the user logs in. They will be printed in the following order:

    run the program
        iprog

    output
        is1 is2

    set the margins using
        mgc, smgl and smgr

    set tabs using
        tbc and hts

    print the file
        if

    and finally
        output is3.

Most initialization is done with is2. Special terminal modes can be set up without duplicating strings by putting the common sequences in is2 and special cases in is1 and is3.

A set of sequences that does a harder reset from a totally unknown state can be given as rs1, rs2, rf and rs3, analogous to is1 , is2 , if and is3 respectively. These strings are output by the reset program, which is used when the terminal gets into a wedged state. Commands are normally placed in rs1, rs2 rs3 and rf only if they produce annoying effects on the screen and are not necessary when logging in. For example, the command to set the vt100 into 80-column mode would normally be part of is2, but it causes an annoying glitch of the screen and is not normally needed since the terminal is usually already in 80 column mode.

The reset program writes strings including iprog, etc., in the same order as the init program, using rs1, etc., instead of is1, etc. If any of rs1, rs2, rs3, or rf reset capability strings are missing, the reset program falls back upon the corresponding initialization capability string.

If there are commands to set and clear tab stops, they can be given as tbc (clear all tab stops) and hts (set a tab stop in the current column of every row). If a more complex sequence is needed to set the tabs than can be described by this, the sequence can be placed in is2 or if.

  Delays and Padding

Many older and slower terminals do not support either XON/XOFF or DTR handshaking, including hard copy terminals and some very archaic CRTs (including, for example, DEC VT100s). These may require padding characters after certain cursor motions and screen changes.

If the terminal uses xon/xoff handshaking for flow control (that is, it automatically emits ^S back to the host when its input buffers are close to full), set xon. This capability suppresses the emission of padding. You can also set it for memory-mapped console devices effectively that do not have a speed limit. Padding information should still be included so that routines can make better decisions about relative costs, but actual pad characters will not be transmitted.

If pb (padding baud rate) is given, padding is suppressed at baud rates below the value of pb. If the entry has no padding baud rate, then whether padding is emitted or not is completely controlled by xon.

If the terminal requires other than a null (zero) character as a pad, then this can be given as pad. Only the first character of the pad string is used.

  Status Lines
Some terminals have an extra `status line' which is not normally used by software (and thus not counted in the terminal's lines capability).

The simplest case is a status line which is cursor-addressable but not part of the main scrolling region on the screen; the Heathkit H19 has a status line of this kind, as would a 24-line VT100 with a 23-line scrolling region set up on initialization. This situation is indicated by the hs capability.

Some terminals with status lines need special sequences to access the status line. These may be expressed as a string with single parameter tsl which takes the cursor to a given zero-origin column on the status line. The capability fsl must return to the main-screen cursor positions before the last tsl. You may need to embed the string values of sc (save cursor) and rc (restore cursor) in tsl and fsl to accomplish this.

The status line is normally assumed to be the same width as the width of the terminal. If this is untrue, you can specify it with the numeric capability wsl.

A command to erase or blank the status line may be specified as dsl.

The boolean capability eslok specifies that escape sequences, tabs, etc., work ordinarily in the status line.

The ncurses implementation does not yet use any of these capabilities. They are documented here in case they ever become important.

  Line Graphics

Many terminals have alternate character sets useful for forms-drawing. Terminfo and curses build in support for the drawing characters supported by the VT100, with some characters from the AT&T 4410v1 added. This alternate character set may be specified by the acsc capability.

.nr 3brule 1
.nr 3crow 4
arrow pointing leftACS_LARROW<,
.nr 3brule 1
.nr 3crow 5
arrow pointing rightACS_RARROW>+
.nr 3brule 1
.nr 3crow 6
arrow pointing upACS_UARROW^-
.nr 3brule 1
.nr 3crow 7
board of squaresACS_BOARD#h
.nr 3brule 1
.nr 3crow 8
bullet ACS_BULLETo~
.nr 3brule 1
.nr 3crow 9
checker board (stipple)ACS_CKBOARD:a
.nr 3brule 1
.nr 3crow 10
degree symbol ACS_DEGREE\f
.nr 3brule 1
.nr 3crow 11
diamond ACS_DIAMOND+`
.nr 3brule 1
.nr 3crow 12
greater-than-or-equal-toACS_GEQUAL>z
.nr 3brule 1
.nr 3crow 13
greek pi ACS_PI*{
.nr 3brule 1
.nr 3crow 14
horizontal line ACS_HLINE-q
.nr 3brule 1
.nr 3crow 15
lantern symbol ACS_LANTERN#i
.nr 3brule 1
.nr 3crow 16
large plus or crossoverACS_PLUS+n
.nr 3brule 1
.nr 3crow 17
less-than-or-equal-toACS_LEQUAL<y
.nr 3brule 1
.nr 3crow 18
lower left cornerACS_LLCORNER+m
.nr 3brule 1
.nr 3crow 19
lower right cornerACS_LRCORNER+j
.nr 3brule 1
.nr 3crow 20
not-equal ACS_NEQUAL!|
.nr 3brule 1
.nr 3crow 21
plus/minus ACS_PLMINUS#g
.nr 3brule 1
.nr 3crow 22
scan line 1 ACS_S1 ~o
.nr 3brule 1
.nr 3crow 23
scan line 3 ACS_S3 -p
.nr 3brule 1
.nr 3crow 24
scan line 7 ACS_S7 -r
.nr 3brule 1
.nr 3crow 25
scan line 9 ACS_S9 _s
.nr 3brule 1
.nr 3crow 26
solid square blockACS_BLOCK#0
.nr 3brule 1
.nr 3crow 27
tee pointing downACS_TTEE+w
.nr 3brule 1
.nr 3crow 28
tee pointing leftACS_RTEE+u
.nr 3brule 1
.nr 3crow 29
tee pointing rightACS_LTEE+t
.nr 3brule 1
.nr 3crow 30
tee pointing up ACS_BTEE+v
.nr 3brule 1
.nr 3crow 31
upper left cornerACS_ULCORNER+l
.nr 3brule 1
.nr 3crow 32
upper right cornerACS_URCORNER+k
.nr 3brule 1
.nr 3crow 33
vertical line ACS_VLINE|x
.nr 3brule 1

The best way to define a new device's graphics set is to add a column to a copy of this table for your terminal, giving the character which (when emitted between smacs/rmacs switches) will be rendered as the corresponding graphic. Then read off the VT100/your terminal character pairs right to left in sequence; these become the ACSC string.

  Color Handling

Most color terminals are either `Tektronix-like' or `HP-like'. Tektronix-like terminals have a predefined set of N colors (where N usually 8), and can set character-cell foreground and background characters independently, mixing them into N * N color-pairs. On HP-like terminals, the use must set each color pair up separately (foreground and background are not independently settable). Up to M color-pairs may be set up from 2*M different colors. ANSI-compatible terminals are Tektronix-like.

Some basic color capabilities are independent of the color method. The numeric capabilities colors and pairs specify the maximum numbers of colors and color-pairs that can be displayed simultaneously. The op (original pair) string resets foreground and background colors to their default values for the terminal. The oc string resets all colors or color-pairs to their default values for the terminal. Some terminals (including many PC terminal emulators) erase screen areas with the current background color rather than the power-up default background; these should have the boolean capability bce.

To change the current foreground or background color on a Tektronix-type terminal, use setaf (set ANSI foreground) and setab (set ANSI background) or setf (set foreground) and setb (set background). These take one parameter, the color number. The SVr4 documentation describes only setaf/setab; the XPG4 draft says that "If the terminal supports ANSI escape sequences to set background and foreground, they should be coded as setaf and setab, respectively. If the terminal supports other escape sequences to set background and foreground, they should be coded as setf and setb, respectively. The vidputs() function and the refresh functions use setaf and setab if they are defined."

The setaf/setab and setf/setb capabilities take a single numeric argument each. Argument values 0-7 of setaf/setab are portably defined as follows (the middle column is the symbolic #define available in the header for the curses or ncurses libraries). The terminal hardware is free to map these as it likes, but the RGB values indicate normal locations in color space.

The argument values of setf/setb historically correspond to a different mapping, i.e.,
It is important to not confuse the two sets of color capabilities; otherwise red/blue will be interchanged on the display.

On an HP-like terminal, use scp with a color-pair number parameter to set which color pair is current.

On a Tektronix-like terminal, the capability ccc may be present to indicate that colors can be modified. If so, the initc capability will take a color number (0 to colors - 1)and three more parameters which describe the color. These three parameters default to being interpreted as RGB (Red, Green, Blue) values. If the boolean capability hls is present, they are instead as HLS (Hue, Lightness, Saturation) indices. The ranges are terminal-dependent.

On an HP-like terminal, initp may give a capability for changing a color-pair value. It will take seven parameters; a color-pair number (0 to max_pairs - 1), and two triples describing first background and then foreground colors. These parameters must be (Red, Green, Blue) or (Hue, Lightness, Saturation) depending on hls.

On some color terminals, colors collide with highlights. You can register these collisions with the ncv capability. This is a bit-mask of attributes not to be used when colors are enabled. The correspondence with the attributes understood by curses is as follows:

For example, on many IBM PC consoles, the underline attribute collides with the foreground color blue and is not available in color mode. These should have an ncv capability of 2.

SVr4 curses does nothing with ncv, ncurses recognizes it and optimizes the output in favor of colors.

  Miscellaneous
If the terminal requires other than a null (zero) character as a pad, then this can be given as pad. Only the first character of the pad string is used. If the terminal does not have a pad character, specify npc. Note that ncurses implements the termcap-compatible PC variable; though the application may set this value to something other than a null, ncurses will test npc first and use napms if the terminal has no pad character.

If the terminal can move up or down half a line, this can be indicated with hu (half-line up) and hd (half-line down). This is primarily useful for superscripts and subscripts on hard-copy terminals. If a hard-copy terminal can eject to the next page (form feed), give this as ff (usually control L).

If there is a command to repeat a given character a given number of times (to save time transmitting a large number of identical characters) this can be indicated with the parameterized string rep. The first parameter is the character to be repeated and the second is the number of times to repeat it. Thus, tparm(repeat_char, 'x', 10) is the same as `xxxxxxxxxx'.

If the terminal has a settable command character, such as the TEKTRONIX 4025, this can be indicated with cmdch. A prototype command character is chosen which is used in all capabilities. This character is given in the cmdch capability to identify it. The following convention is supported on some UNIX systems: The environment is to be searched for a CC variable, and if found, all occurrences of the prototype character are replaced with the character in the environment variable.

Terminal descriptions that do not represent a specific kind of known terminal, such as switch, dialup, patch, and network, should include the gn (generic) capability so that programs can complain that they do not know how to talk to the terminal. (This capability does not apply to virtual terminal descriptions for which the escape sequences are known.)

If the terminal has a ``meta key'' which acts as a shift key, setting the 8th bit of any character transmitted, this fact can be indicated with km. Otherwise, software will assume that the 8th bit is parity and it will usually be cleared. If strings exist to turn this ``meta mode'' on and off, they can be given as smm and rmm.

If the terminal has more lines of memory than will fit on the screen at once, the number of lines of memory can be indicated with lm. A value of lm#0 indicates that the number of lines is not fixed, but that there is still more memory than fits on the screen.

If the terminal is one of those supported by the UNIX virtual terminal protocol, the terminal number can be given as vt.

Media copy strings which control an auxiliary printer connected to the terminal can be given as mc0: print the contents of the screen, mc4: turn off the printer, and mc5: turn on the printer. When the printer is on, all text sent to the terminal will be sent to the printer. It is undefined whether the text is also displayed on the terminal screen when the printer is on. A variation mc5p takes one parameter, and leaves the printer on for as many characters as the value of the parameter, then turns the printer off. The parameter should not exceed 255. All text, including mc4, is transparently passed to the printer while an mc5p is in effect.

  Glitches and Braindamage

Hazeltine terminals, which do not allow `~' characters to be displayed should indicate hz.

Terminals which ignore a line-feed immediately after an am wrap, such as the Concept and vt100, should indicate xenl.

If el is required to get rid of standout (instead of merely writing normal text on top of it), xhp should be given.

Teleray terminals, where tabs turn all characters moved over to blanks, should indicate xt (destructive tabs). Note: the variable indicating this is now `dest_tabs_magic_smso'; in older versions, it was teleray_glitch. This glitch is also taken to mean that it is not possible to position the cursor on top of a ``magic cookie'', that to erase standout mode it is instead necessary to use delete and insert line. The ncurses implementation ignores this glitch.

The Beehive Superbee, which is unable to correctly transmit the escape or control C characters, has xsb, indicating that the f1 key is used for escape and f2 for control C. (Only certain Superbees have this problem, depending on the ROM.) Note that in older terminfo versions, this capability was called `beehive_glitch'; it is now `no_esc_ctl_c'.

Other specific terminal problems may be corrected by adding more capabilities of the form xx.

  Similar Terminals

If there are two very similar terminals, one (the variant) can be defined as being just like the other (the base) with certain exceptions. In the definition of the variant, the string capability use can be given with the name of the base terminal. The capabilities given before use override those in the base type named by use. If there are multiple use capabilities, they are merged in reverse order. That is, the rightmost use reference is processed first, then the one to its left, and so forth. Capabilities given explicitly in the entry override those brought in by use references.

A capability can be canceled by placing xx@ to the left of the use reference that imports it, where xx is the capability. For example, the entry

    2621-nl, smkx@, rmkx@, use=2621,

defines a 2621-nl that does not have the smkx or rmkx capabilities, and hence does not turn on the function key labels when in visual mode. This is useful for different modes for a terminal, or for different user preferences.

  Pitfalls of Long Entries

Long terminfo entries are unlikely to be a problem; to date, no entry has even approached terminfo's 4096-byte string-table maximum. Unfortunately, the termcap translations are much more strictly limited (to 1023 bytes), thus termcap translations of long terminfo entries can cause problems.

The man pages for 4.3BSD and older versions of tgetent() instruct the user to allocate a 1024-byte buffer for the termcap entry. The entry gets null-terminated by the termcap library, so that makes the maximum safe length for a termcap entry 1k-1 (1023) bytes. Depending on what the application and the termcap library being used does, and where in the termcap file the terminal type that tgetent() is searching for is, several bad things can happen.

Some termcap libraries print a warning message or exit if they find an entry that's longer than 1023 bytes; others do not; others truncate the entries to 1023 bytes. Some application programs allocate more than the recommended 1K for the termcap entry; others do not.

Each termcap entry has two important sizes associated with it: before "tc" expansion, and after "tc" expansion. "tc" is the capability that tacks on another termcap entry to the end of the current one, to add on its capabilities. If a termcap entry does not use the "tc" capability, then of course the two lengths are the same.

The "before tc expansion" length is the most important one, because it affects more than just users of that particular terminal. This is the length of the entry as it exists in /etc/termcap, minus the backslash-newline pairs, which tgetent() strips out while reading it. Some termcap libraries strip off the final newline, too (GNU termcap does not). Now suppose:

*   a termcap entry before expansion is more than 1023 bytes long,

*   and the application has only allocated a 1k buffer,

*   and the termcap library (like the one in BSD/OS 1.1 and GNU) reads the whole entry into the buffer, no matter what its length, to see if it is the entry it wants,

*   and tgetent() is searching for a terminal type that either is the long entry, appears in the termcap file after the long entry, or does not appear in the file at all (so that tgetent() has to search the whole termcap file).

Then tgetent() will overwrite memory, perhaps its stack, and probably core dump the program. Programs like telnet are particularly vulnerable; modern telnets pass along values like the terminal type automatically. The results are almost as undesirable with a termcap library, like SunOS 4.1.3 and Ultrix 4.4, that prints warning messages when it reads an overly long termcap entry. If a termcap library truncates long entries, like OSF/1 3.0, it is immune to dying here but will return incorrect data for the terminal.

The "after tc expansion" length will have a similar effect to the above, but only for people who actually set TERM to that terminal type, since tgetent() only does "tc" expansion once it is found the terminal type it was looking for, not while searching.

In summary, a termcap entry that is longer than 1023 bytes can cause, on various combinations of termcap libraries and applications, a core dump, warnings, or incorrect operation. If it is too long even before "tc" expansion, it will have this effect even for users of some other terminal types and users whose TERM variable does not have a termcap entry.

When in -C (translate to termcap) mode, the ncurses implementation of tic(1M) issues warning messages when the pre-tc length of a termcap translation is too long. The -c (check) option also checks resolved (after tc expansion) lengths.

  Binary Compatibility
It is not wise to count on portability of binary terminfo entries between commercial UNIX versions. The problem is that there are at least two versions of terminfo (under HP-UX and AIX) which diverged from System V terminfo after SVr1, and have added extension capabilities to the string table that (in the binary format) collide with System V and XSI Curses extensions.

EXTENSIONS
Some SVr4 curses implementations, and all previous to SVr4, do not interpret the %A and %O operators in parameter strings.

SVr4/XPG4 do not specify whether msgr licenses movement while in an alternate-character-set mode (such modes may, among other things, map CR and NL to characters that do not trigger local motions). The ncurses implementation ignores msgr in ALTCHARSET mode. This raises the possibility that an XPG4 implementation making the opposite interpretation may need terminfo entries made for ncurses to have msgr turned off.

The ncurses library handles insert-character and insert-character modes in a slightly non-standard way to get better update efficiency. See the Insert/Delete Character subsection above.

The parameter substitutions for set_clock and display_clock are not documented in SVr4 or the XSI Curses standard. They are deduced from the documentation for the AT&T 505 terminal.

Be careful assigning the kmous capability. The ncurses wants to interpret it as KEY_MOUSE, for use by terminals and emulators like xterm that can return mouse-tracking information in the keyboard-input stream.

Different commercial ports of terminfo and curses support different subsets of the XSI Curses standard and (in some cases) different extension sets. Here is a summary, accurate as of October 1995:

SVR4, Solaris, ncurses -- These support all SVr4 capabilities.

SGI -- Supports the SVr4 set, adds one undocumented extended string capability (set_pglen).

SVr1, Ultrix -- These support a restricted subset of terminfo capabilities. The booleans end with xon_xoff; the numerics with width_status_line; and the strings with prtr_non.

HP/UX -- Supports the SVr1 subset, plus the SVr[234] numerics num_labels, label_height, label_width, plus function keys 11 through 63, plus plab_norm, label_on, and label_off, plus some incompatible extensions in the string table.

AIX -- Supports the SVr1 subset, plus function keys 11 through 63, plus a number of incompatible string table extensions.

OSF -- Supports both the SVr4 set and the AIX extensions.

FILES

/usr/pkg/share/terminfo/?/*
    files containing terminal descriptions

SEE ALSO
tic(1M), infocmp(1M), curses(3X), printf(3), term(5). term_variables(3X).

AUTHORS
Zeyd M. Ben-Halim, Eric S. Raymond, Thomas E. Dickey. Based on pcurses by Pavel Curtis.